2026.11.16
Events
[Activity Report]Orfit Splinting Workshop 2026 in Osaka and Aichi

Hands-On Upper Limb Splint Workshop Led by Orfit Clinical Instructor were held in two locations: Osaka & Aichi!
We invited Mr. Björn Le Roy, Orfit Product Specialist from Orfit Industries, to Japan to lead the workshops at two different venues.
Based in Belgium, Mr. Björn Le Roy is an occupational therapist who also regularly visits hospitals in Germany and other countries. Drawing on his extensive practical experience, he shared valuable insights, including real-life clinical cases and practical tips for splint fabrication.
Over the two-day workshops, participants fabricated a total of five different types of splints. It was a packed program with plenty of hands-on practice! Here's a report on what took place during these two exciting days.
Day1
Short Opponens Splint (Thumb Post Splint) using Orfit Classic

We started by fabricating a Short Opponens Splint. The instructor first demonstrated the fabrication process, explaining the recommended dimensions for cutting the thermoplastic sheet and highlighting important points to keep in mind during fabrication.
After the demonstration, participants began making their own splints. Ample time was allocated for the hands-on session, allowing even those with no prior experience in splint fabrication to work at their own pace while checking with and receiving guidance from the instructor whenever needed.
Cock-up Wrist Splint using Orfit Aquafit NS

The second splint was a Cock-up Splint. As with the Short Opponens Splint, participants first determined the appropriate sheet size and cutting lines, then take a mold to establish the correct dimensions.
There are two types of Cock-up Splints: palmar flexion and dorsiflexion. The instructor explained the advantages of each type, and for this session, participants fabricate the dorsiflexion version.
Day 2
Mallet Finger Splint using Orficast

On Day 2, participants fabricated splints using Orficast. Since Orficast has different properties from conventional thermoplastic sheets, there are some differences in how it should be handled during the fabrication process. After the instructor's explanations and demonstration, participants began fabricating their own splints.

Orficast is available in two colors, blue and black. For this session, the black material was used, which makes the splints somewhat difficult to see clearly in the photographs.
Anti-Swan Neck Splint using Orficast

These are the splints fabricated by the instructor. Both the cut edges and the joints have been neatly finished.
Using different sizes of Orficast, the instructor fabricated two types of splints, each following a different fabrication process.
PIP Dynamic Splint using Orficast

The final project of the workshop was the fabrication of a Dynamic Splint, which involved the most steps of all the splints covered during the session. Many participants found this one particularly challenging.
Since the splint was made using Orficast, it provided a good fit around the fingers. The wire spring is a key component of this splint. However, Orfit offers it as a pre-made splint component, so participants did not need to wind the spring from scratch. They only needed to cut the wire to the required length to complete the fabrication.
A Special Thank You to Our Instructor!

As an occupational therapist with extensive experience in splint fabrication, Mr. Björn Le Roy shared a wealth of knowledge with us, including fabrication techniques, step-by-step procedures, and practical tips for achieving a proper fit.
Mr. Björn Le Roy also conducted an in-house training session for our staff, giving us the opportunity to learn about current splint fabrication practices in Europe and explore new fabrication techniques.
During the workshops, participants were particularly impressed by his professional and flexible approach. He demonstrated how to identify the key points in the fabrication process and how to adjust the splint's shape and cut lines according to the required joint support and each individual case. His ability to adapt his techniques to meet different clinical needs was truly impressive.
We would like to take this opportunity to express our sincere gratitude to Mr. Björn Le Roy for sharing his valuable knowledge, skills, and experience with us.
Afterwords...
We were delighted to welcome Mr. Björn Le Roy to Japan for the first time and hold two workshops, giving occupational therapists involved in splint fabrication across Japan the opportunity to participate and learn from his expertise.
We would also like to express our sincere appreciation to the Japan Hand Therapy Society (JHTS) for their generous support in selecting the venues, promoting the workshops, and helping us attract participants.
We also offer samples of Orfit products and hold online workshops. We are committed to supporting everyone who is interested in fabricating splints using Orfit products. If you are interested, please feel free to contact us and take advantage of these opportunities!
